How to install spark plug wires on a gl1100

#How to install spark plug wires on a gl1100 driver

Leaving the radiator through the bottom hose the cooled fluid is pumped around the engine again.Д¬ars operate in a wide variety of temperatures. The radiator transfers the heat from the fluid to the air pulled through the exchanger by a fan. Then, having entered through the top hose the hot fluid passes through the heat exchanger or radiator. Flowing around the engine the fluid absorbs its heat, which consequently allows the engine to get cooled. Most cars are equipped with liquid-cooling systems. The alternative is a liquid (water)-cooling system. However, it is difficult to design large engines with an unobstructed airflow over all the cylinders. The forced airflow conducts heat away from the cylinders radiating it into the air more efficiently. A powerful fan is used to supply an increased amount of air for cooling multi-cylinder engines. Constructing the engine block covered in numerous external aluminum fins engineers greatly increase its surface area, which can be cooled by the flow of air passing over it. Some older cars, very few modern cars and most motorcycle have air-cooled engines. There are two types of cooling systems found on cars: air-cooled and liquid-cooled. So, another important job of the cooling system is to allow the engine to heat up as quickly as possible, and then to keep the engine at a constant temperature. When the engine is cold, components wear out faster, and the engine is less efficient and emits more pollution. The engine in your car runs best at a fairly high temperature. However, the cooling system also has several other important jobs. In fact, the cooling system on a car driving down the freeway dissipates enough heat to heat two average-sized houses! The primary job of the cooling system is to cool the engine and to keep it from overheating. About half of this heat goes down the exhaust pipe and the other half stays in the engine making it very hot. But only a quarter of this energy makes the pistons move. Why?Д«urning in the engine the fuel-air mixture produces energy. When you drive a car, the engine becomes very hot. Learn the following words and word-combinations to comprehend the text. This consequently breaks the electrical contact switching off the fuel warning light on the instrument panel of the car. Being forced upwards the float moves the arm in the same direction (up) raising the lever. When rising, the fuel level pushes the float up.

#How to install spark plug wires on a gl1100 driver

Having noticed the fuel warning light the driver should put more petrol (D) into the tank. This makes the arm go down as well allowing the lever to touch an electrical contact and thus switching on the fuel light in the car. When falling, the level of the fuel causes the float to move downwards. What makes this light work? The tank is equipped with a special float (E) indicating the level of the fuel in it. The light switches on in order to enable the driver to see when the level of fuel (C) in the tank becomes critical.

Its function is to prevent your stopping in the middle of the road with an empty tank (B). What is it? Certainly, a fuel warning light (A). Having noticed it on the instrument panel of your car you start looking for a petrol station. Write a set of instructions 'How to maintain a car'. You are a mechanic at the service station. you should do it to keep your car reliable. if you want to stop you should push it ДЎ1. the fuel warning light shows that the tank is вЂ¦ ДЁ. part of the engine where fuel is mixed with air Д¦. Caution should be taken not to overtighten the plug. Next, it is necessary to place the spanner over the plug and give ONLY a quarter turn clockwise. Having replaced the plug in the socket you should rotate it clockwise until it is hand-tight. Check that the вЂ¦ is between 0.65 and 1.00 mm wide. Having removed the plug from the вЂ¦, examine the gap and check it to be clean. Then it is necessary to rotate the вЂ¦ antiВclockwise until it seems to be loose. Having achieved this, place the вЂ¦ over the spark plug. At the same time, insufficient tightening can lead to overheating of the spark plug and potential detonation.First you should remove the cover.

This is very important, as excessive tightening of a spark plug can cause breakage of the metal shell and damage to the interior seals. Then seat the plug/gasket with a torque or turning angle wrench as specified in the chart below. First, screw in the plug finger tight until the gasket meets the cylinder head. It is essential to tighten a spark plug to the specified turning angle or torque setting.